Join our mailing list!
You are here: Home > DICKEY-john Products > Misc.
Sort By:
Page of 1  
1/2-4 in. poly Flow Meters
Our Price:

Flow Meters 1/2-2 in. poly
1/2-2 in. poly flow meter assemblies include:
Flow meter body with turbine, axle and bearings, hall effect sensor with three-pin weather pack connector, hose barbs for inlet and outlet, Viton O-rings, and coupling nuts.
 
Flow Meters 3-4 in. poly
3-4 in. poly flow meter assemblies include:
Flow meter body with turbine, axle and bearings, hall effect sensor with three-pin weather pack connector, flanges with Viton O-rings for inlet and outlet, and flat flanges, but no O-rings.

Sensor-1 Part Number                           DICKEY-john Part Number
DJ-1/2PFM.....................................PM00370018
DJ-3/4 PFM....................................PM00370023S1
DJ-1PFM........................................PM00370030
DJ-1-1/2PFM...................................PM00370040
DJ-2PFM........................................PM00370048S1
DJ-3.0 PFM.....................................PM00370068
DJ-4.0PFM......................................PM00370088
Application Rate Sensor
Our Price: $209.00

Measures shaft rotation speed, outputs at 360 pulses per revolution for increased accuracy, RPM range 2-2,500, easily adapts to 1 and 1 1/4 in. diameter shafts, and 12 volt sensor with square-wave signal output.

Comes with cable 1’ up to 30”  Part# for sensor w/1’ cable 46436-0177S1
Implement Lift Switch
Our Price: $95.00

Enables or disables implement function.  Attaches to three-point hitch or lift cylinder. Ties to planter monitors and control systems.

DICKEY-john part number: 46372-0150S
Liquid Pressure Sensor
Our Price: $920.00

Measures 0-650 psi liquid pressure, can be used as an alternative to flow meter in a Land Manager® or CCS100 liquid sprayer control systems, reads liquid pressure at nozzle on spray bar. Prevents over-application caused by single nozzle clogs.

DICKEY-john Part Number: 46570-0020
Liquid Flow Control Valves
Our Price:

3/8-3 in. sizes for liquid flow control of 0.80 to 600 gpm Stainless steel ball valves from 3/8-1 in. for flow control of 0.80 to 80 gpm. 2 or 3 in. butterfly valves for control of 220 to 600 gpm. Use the following information to help you choose the right flow control valve for your equipment.
Valve Actuator
Our Price:

Valve Actuator
From closed to open in 1.5 seconds. Environmentally sealed Drives 3/8 to 1 in. liquid and NH3 control valves. Use the following information to help you choose the right flow control valve for your equipment.
Liquid Flow Rate Formula
To calculate liquid flow rates (gpm) so you can pick the correct Flow Control Valve for your application, use the following formula:
Width x speed x application rate (gpa) x 0.00202 = gpm
Example: 60 ft. x 15 mph x 20 gpa x 0.00202 = 36.36 gpm
Proportional Hydraulic Flow Control Valves
Our Price:

Proportional Hydraulic Flow Control Valves
Available in 4 and 8 gpm sizes. Operating pressure inlet 3,500 psi (240 bar) Regulated flow rate 0-4 gpm (0-15 lpm), 0-8 gpm (0-30 lpm) Reverse free flow cracking pressure 15-20 psi (1-1.4 bar) Internal leakage 0.10 gpm (0.38 lpm) at zero current. Coil voltage 12 VDC Maximum control current of 1,500 ±100 mA Use the following information to help you choose the right flow control valve for your equipment.
Liquid Flow Rate Formula
To calculate liquid flow rates (gpm) so you can pick the correct Flow Control Valve for your application, use the following formula: Width x speed x application rate (gpa) x 0.00202 = gpm
Example: 60 ft. x 15 mph x 20 gpa x 0.00202 = 36.36 gpm

Sensor-1 Part Number                   DICKEY-john Part Number
DJ-4GPM......................................46709-2004S1
DJ-8GPM......................................46709-2008S1